Kraton 4wd Rtr Green

Quantity: 1
    This is the Electric Powered, 2.4GHz Radio Controlled 1/8th scale,      
               Ready to Run Kraton 6S BLX Speed Truck from ARRMA.              
                                                                               
           The version of the Kraton 6S BLX released in October 2017           
   (ARAD81LG, ARAD81LR) features the following differences and upgrades;       
                                                                               
    **New Larger Battery Tray w/Wire Routing Clip & area for Balance Plug**    
              **Radio Box w/Rubber Wire Seals & Receiver Plate**               
          **Aluminum Top & Bottom Shock Caps & Preload Adjusters**             
     **Larger Diameter 0.16" (4mm) Shock Shafts & New High Spring Perches**    
        **Additional Webbing Added to Bulkheads for Greater Strength**         
             **Stronger Servo Mount for Better Steering Feel**                 
           **Updated Chassis Braces Attach Directly to Chassis**               
           **Lightweight Plastic Shock and Roll Bar Pivot Balls**              
     **Added Material Around Front Suspension Arms for Greater Strength**      
                                                                               
FEATURES: Chassis: 0.12" (3mm) thick aluminum, black in color                  
          Drive: Four wheel with CVD driveshafts                               
          Radio: Tactic TTX300 2.4GHz 2-channel with                           
          Steering Servo: ADS-15M waterproof, 195 oz-in (149 kg-cm) torque @6V,
            0.16sec speed @6V, metal gear, 25 tooth spline output              
          Motor: BLX4074 2050Kv 4-pole brushless (ARAG2000)                    
          ESC: Waterproof BLX185 150A 6S with built-in cooling fan, and male   
            XT90 connector                                                     
          Radio Box: New design routes ESC & receiver wires through a rubber   
            seal to avoid pinching when lid is replaced, receiver is attached  
            to a plate that slots into receiver box base, one-piece rubber     
            seal seals out water and dirt                                      
          Shocks: 16mm red anodized aluminum body, oil filled, aluminum top    
            and bottom caps, 0.16" (4mm) diameter shaft, new high spring perch 
          Shock Towers: 0.20" (5mm) thick aluminum, black in color             
          Suspension: Pivot ball with anti-roll bar                            
          Differentials: Three metal gear                                      
          Roll Cage: Composite internal                                        
          Body: Trimmed and painted polycarbonate, nylon rear wing             
          Motor Mount: Aluminum                                                
          Battery Tray: From the Outcast 6S, with front to back battery strap, 
            wire routing clips, balance plug stowage, higher sides for better  
            fit, and front upper cap that adjusts to battery height when       
            battery strap is tightened                                         
          Tires: dBoots Minokawa, width: 3.3" (85mm), diameter: 6.2" (157mm)   
          Wheels: Five split spoke, black in color 17mm hex, diameter: 3.8"    
            (97mm), width 2.6" (66mm)                                          
          Camber: Adjustable front and rear, camber refers to the angle of the 
            tops of the tires from vertical when viewed from front or behind   
            vehicle                                                            
          Caster: Adjustable, caster/toe-in refers to the angle of the front   
            suspension when viewed from the side of the car in relation to     
            the chassis                                                        
          Warranty: Two year limited warranty beginning at date of purchase    
                                                                               
INCLUDES: RTR Kraton 6S BLX Speed Truck with Painted Body, 2.4GHz Radio,       
            Waterproof Steering Servo and Receiver Box, BLX185 ESC, 2050Kv     
            Brushless Motor, 12T Pinion Gear, Instruction Manual. two XT90     
            Battery Connectors and Bridging Wire for single pack use           
                                                                               
REQUIRES: AA Batteries: Four for transmitter                                   
          LiPo Battery: Two 2-3S 5000mAh 35C minimum LiPo with XT90            
            connector, Onyx 11.1V 5000mAh 35C batteries recommended, or one    
            4-6S LiPo battery                                                  
          Battery Charger: To match selected battery                           
          LiPo charging sack, building & track equipment                       
                                                                               
SPECS:      Vehicle-                                                           
_         Length: 23.39 in (594mm)                                             
          Front and Rear Width: 18.11 in (460mm)                               
          Height: 7.68 in (195mm)                                              
          Wheelbase: 14.84 (377mm)                                             
          Ride Height: 1.85" (47mm)                                            
          Weight: 9.15lb (4.5kg)                                               
          Maximum Battery Tray Dimensions: 6.22 x 2.76 x 1.89"                 
            (158 x 70 x 49mm)                                                  
                                                                               
            Body-                                                              
          Length: 18.6"  (472mm)                                               
          Width:   8"    (203mm) behind front wheels, narrowest point          
          Width:  10.03" (255mm) at rear wheels, widest point                  
          Height:  6.25" (159mm)                                               
                                                                               
COMMENTS: Available in the following body color schemes;                       
            Green/Black, ARAD81LG                                              
            Red/Black, ARAD81LR                                                
                                                                               
COMMENTS: For replacement ball bearings use:                                   
          Qty.  Size      Location        Qty.      Bearing Set                
           2   15x21mm    F&R Inner Hubs   1          ARAC3162                 
           2   8x16mm     F&R Inner Hubs   1          ARAC3156                 
           2   5x10mm     Idler Gear       1          ARAC3200                 
           2   5x10mm     Input Shaft      1          ARAC3200                 
           2   10x15mm    Diff Gear        1          ARAC3202                 
           6   8x16mm    Fr, Ctr & R Diffs 3          ARAC3156                 
                                                                               
          The BLX185 ESC was set from factory to default to a LiPo battery     
            mode.                                                              
          If any adjustments such as recalibration were made, check to see     
          that the battery mode has not been inadvertently set to NiMH mode.   
          Follow these steps to verify battery mode;                           
          1. Raise the vehicle chassis so that the wheels are not touching     
             anything.                                                         
          2. With the battery or batteries charged and connected to the        
             vehicle's ESC leads, switch on the transmitter and then switch    
             on the vehicle. If a green LED flashes once the ESC is in LiPo    
             mode. If there is no LED flash on the ESC, and a pulsing noise    
             is made by the motor, the ESC is in NiMH mode. If you intend to   
             use LiPo batteries DO NOT operate ESC in NiMH mode, the           
             batteries may be damaged.                                         
                                                                               
          To switch ESC from NiMH mode to LiPo mode perform the following      
             steps;                                                            
          1. Connect battery, switch on transmitter, press and hold set        
             button and turn on ESC. The red LED will flash.                   
          2. Keep holding set button until green LED flashes. The number of    
             flashes represents the variable number of attributes being        
             programmed.                                                       
          3. To enter the battery mode programming function, release the set   
             button when one green LED flashes.                                
          4. Press the set button to change battery mode between LiPo and      
             NiMH. One RED LED flash indicates ESC is set to LiPo mode.        
          5. To save setting, switch ESC off.       
0 stars based on 0 reviews